Flat Roof Leak Repair Products- Harrisburg PA Youtube

If you have shingles on a Mobile Home that starts to leak, then this is your best option. This will ensure that you don't waste money on repairs, but buy a small section of new roofing each time you repair a leak.

25 1

How to seal an RV/ Tuck Camper roof – never have to do it again
#rvlife #campers
@AllRoof.

18 2

Making a transition from a carport roof or attached room to a Mobile Home.
#mobilehomes #mobile
@AllRoof.

23 3

We got a text from a stranger asking for help. So we did fix his roof and see what happened
@AllRoof.
Turbo Poly Seal – https://bergstromm.com/

See the full version in the link below.
https://youtube.com/shorts/RadJ8lQI5dE

50 3

We helped a random person fix his mobile home roof from leaking
You could be the next one we help – See the phone number at the end of the video and text me your info – we will choose the lucky one and call you to fix your roof for you
Turbo Poly Seal – https://bergstromm.com/

83 5

Someone contacted us via text message and asked if we could help fix the leaks on his mobile home. When we got there, we were a little shocked by how bad it was. Instead of a repair, we also did a section of his roof.
Turbo Poly Seal – https://bergstromm.com/

Chapters:
0:00 Mobile Home Roof leak repair
1:39 Analyzing the roof
4:00 Preparing to make transition
5:20 Installing Rubber roof material
9:46 Making transition from rubber to metal roof

44 6

If you want to seal your RV/ Truck camper roof once and for all, then this is the method. It requires a lot of work and is somewhat costly, but ultimately, it is worth it.
Turbo Poly Seal and Super Silicone Seal – https://bergstromm.com/

16-step instructions for preparing and sealing an RV or truck camper roof:

1. Remove obstacles: Detach any roof racks or attachments that block access to the roof surface.

2. Strip old materials: Use an angle grinder with a steel-bristle brush to clear away caulk, paint buildup, and residue.

3. Expose critical areas: Strip paint around the air vent flashing and at least two inches beyond it.

4. Clean joints: Remove sealant or caulking along the roof perimeter and joints.

5. Prepare the surface: Use the angle grinder to take off most of the old paint—there’s no need to grind down to bare metal.

6. Clear debris: Blow the roof clean of dust using a leaf blower.

7. Wipe down: Use lacquer thinner to clean the entire surface; this is essential since the grinder can melt and spread silicone.

8. Tape off edges: Apply painter’s tape around the perimeter, leaving a 1.5-inch space from the termination bar.

9. Apply base coat: Brush a thick coat of Turbo Poly Seal over the termination bar and onto the roof.

10. Install fleece: Cut polyester fleece into two-inch strips and place them over the termination bar, ensuring no gaps underneath.

11. Seal the fleece: Apply another coat of Turbo Poly Seal to fully cover the fleece.

12. Add protective coat: After about 40 minutes, apply a coat of Silver Coat protection over the Turbo Poly Seal.

13. Remove tape: Carefully pull off the painter’s tape.

14. Final roof coating: Wait 24 hours, then use a nine-inch roller with a quarter-inch nap to evenly apply Super Silicone Seal across the roof.

15. Cure time: Allow the silicone to cure for 48 hours before walking on the roof.

16. Reattach fixtures: Once everything is cured, reinstall the roof racks and any other attachments.

Chapters:
0:00 How to Seal RV Camper Roof
1:05 Cleaning up old caulking and paint
4:55 Lacquer Thiiners to wipe everything clean
5:35 Applying Turbo Poly Seal on the edges
7:05 Coat entire surface with Super Silicone Seal






Chapters:
0:00 RV camper roof sealed
1:05 Cleaning and preparing
5:26 Seal the trim with Turbo Poly Seal
7:08 Coating roof with Super Silicone Seal
8:45 Results are amazing

52 8

Super Silicone Seal is easy and fast to fix leaks on rusted metal roofs, ducts, EPDM rubber roofs, and skylights #diy #airconditioner
Super Silicone Seal – https://bergstromm.com/
Steps on Repairing Rusted Metal of Roofs and Air Conditioning Ducts;
1. Remove the rust, caulking, and other materials used by others before
2. Use an angle grinder with a steel brush to clean most debris off
3. Use Lacquer Thinner to wipe any old tar, silicone, or oils off
4. Pour out Super Silicone Seal over the surface and spread it with a brush
5. Use a Polyester Fleece to cover seams and pin holes
6 Add another coat of sealant over the fleece

116 5

Super Silicone Seal is easy and fast to fix leaks on rusted metal roofs, ducts, EPDM rubber roofs, and skylights #diy #airconditioner

17 Steps for repairing rusted metal on roofs and air‑conditioning ducts using Super Silicone Seal:

1. Prepare and clean the area: Remove all rust, old caulk, tar, paint, and other coatings. Start with a flat bar or hammer claw to pry off large chunks, then use an angle grinder with a wire brush or 120‑grit sandpaper to strip away remaining silicone, asphalt, and paint until the metal is clean and slightly rough
2. Wear gloves and eye protection.
3. Wipe the surface: After grinding, wipe the area with a rag soaked in lacquer thinner to remove tar, silicone residue, or oils that could prevent adhesion
4. Let the surface dry completely.
5. Mask off the repair zone: For a neat finish, apply painter’s tape roughly 2½ inches on either side of the crack, seam, or hole
6. Replace any rusted screws with new pan‑head screws before sealing to minimize movement
7. First coat: Use a paintbrush to apply a generous coat of Super Silicone Seal over the cleaned area, extending at least 2 inches beyond the damage
8. On cylindrical surfaces like ducts, cut small tabs into the polyester fleece so it can wrap neatly
9. Embed fleece: Immediately press a strip of polyester fleece into the wet sealant. Work out all air bubbles and wrinkles so the fabric sits flat and fully contacts the sealant
10. The fleece reinforces the repair and spans seams and pinholes.
11. Second coat: Apply a second coat of Super Silicone Seal over the fleece, saturating it thoroughly and making sure no fibers are exposed
12. For ducts or pipes, wrap the fleece around the entire circumference and coat it thoroughly
13. Finishing and cure time: Remove the painter’s tape while the sealant is still wet for clean edges
14. The sealant skins over in about 30 minutes and can withstand rain after roughly one hour, but it needs about 24 hours to cure fully
15. During this period, avoid walking on or disturbing the repair.
16. Optional topcoat and clean‑up: A protective topcoat can be applied after 4–12 hours if additional UV protection or colour matching is desired
17. Wipe away any drips with a clean rag and discard used brushes. Remember to wear gloves, use disposable brushes, and keep safety glasses on throughout the process
Chapters:
0:00 – AC Duct rusted with holes
0:15 – Preparing the surface
0:34 – Pouring Super Silicone Sealant
1:18 – Results after 5 years

25 1

These Hidden leaks can cost you a lot of money if you don't know where to look.
Super Silicone Seal – https://bergstromm.com/

154 6

Most people are caught by surprise when they can't find this leak. Not everyone is aware of this leak and will give up looking for it. After many, many trips to this roof, I finally figured out where the roof was leaking
Super Silicone Seal – https://bergstromm.com/
Chapters:
0:00 Hidden leak on a Metal Roof
0:33 Metal snips and cut the seam open
1:04 Use the grinder to clean
1:16 Lacquer thinners to clean
1:27 Super Silicone Seal to seal Hidden seam

25 6

How to repair a flat roof leak in less than a minute
Turbo Poly Seal – https://bergstromm.com/
8 Steps on Making a Roof Repair:
1. Locate the leaky area. Most likely around vent pipes, flashing, and penetrations through the roof
2. If necessary, brush off any dirt or debris so it is dust-free.
3. If cualking was used before, remove it.
4. Use Turbo Poly Seal – Stir the content.
5. Brush 1 coat over the area of repair
6. Cut a piece of the Polyester Fleece and place it over the 1st coat
7. Paint a final coat covering the fleece entirely.
8. If necessary, a Silver Coat Protection can be used to coat over the Turbo Poly Seal after it is cured to protect against ultraviolet light.

250 5

Repairing a valley from leaking on a Metal Roof #diy #metalroofing
Turbo Poly Seal – https://bergstromm.com/

8 Steps to Making a Roof Repair:
1. Where more than 1 metal panel crosses over another can cause leaks, like a valley
2. If necessary, brush off any dirt or debris so it is dust-free.
3. If cualking was used before, remove it.
4. Use Turbo Poly Seal – Stir the content.
5. Brush 1 coat over the area of repair
6. Cut a piece of the Polyester Fleece and place it over the 1st coat
7. Paint a final coat covering the fleece entirely.
8. If necessary, a Silver Coat Protection can be used to coat over the Turbo Poly Seal after it is cured to protect against Ultra Violets

137 9

How to stop leaks on a Metal Roof Valley
Turbo Poly Seal – https://bergstromm.com/

20 1

Repair A/C Curb flashing with what I had on the roof
Super Silicone Seal – https://bergstromm.com/

95 5

Watch this video before you coat a roof. Metal roofs should not be coated
Super Silicone Seal – https://bergstromm.com/

142 3

Watch this before you have your roof coated; it will save you a lot of money. Also, how to make a seam repair.
Super Silicone Seal – https://bergstromm.com/

Chapters:
0:00 Why not coat a metal roof
1:00 Preparing the seam
1:27 Seal seam with Super Silicone Seal
1:56 Results of previous repair

44 2

Seal an AC wall unit from leaking
Super Silicone Seal – https://bergstromm.com/

154 12

How to repair a leaky seam on a flat roof
Turbo Poly Sewal – https://bergstromm.com/

8 Steps to Making a Roof Repair:
1. When a Rubber Roof Seam needs to be sealed
2. If necessary, brush off any dirt or debris so it is dust-free.
3. If cualking was used before, remove it.
4. Use Turbo Poly Seal – Stir the content.
5. Brush 1 coat over the area of repair
6. Cut a piece of the Polyester Fleece and place it over the 1st coat
7. Paint a final coat covering the fleece entirely.
8. If necessary, a Silver Coat Protection can be used to coat over the Turbo Poly Seal after it is cured to protect against ultraviolet light.

184 5

Easiest, fastest rubber roof installation for any DIYer. No skills are needed, and it will last 20-30 years. You can almost install this over any surface.
Turbo Poly Seal – https://bergstromm.com/

Chapters:
0:00 How to Install a Rubber Roof
0:35 Parapet wall in bad shape
1:05 Screw down surface
2:48 Laying down base sheet
3:53 Laying down the Cap sheet
4:18 Prep parapet wall for membrane
5:19 Installing membrane over parapet wall
8:49 Vent flashing
9:56 Results after 3 years

59 8

You are crazy not to apply Silver Coat protection for your roof. This will protect it against Ultraviolets and also reduce the temperature by 60º

Chapters:
0:00 Silver Coat Protection
0:24 The purpose of Silver Coating
1:16 Spider cracks due to UVs
2:32 Repairing holes in the roof
3:22 How to repair a seam on Torch Down Roof

50 15

What is the purpose of a Gutter filter?
Gutter Filter – https://bergstromm.com/product/z-gutter-leaf-filter/

152 5

Repairing a shingle that is leaking on our church
Turbo Poly Seal – https://bergstromm.com/

7 Steps to Making a Roof Repair:
1. Repairs where shingles have blown off or nails are showing
2. If necessary, brush off any dirt or debris so it is dust-free.
3. If cualking was used before, remove it.
4. Use Turbo Poly Seal – Stir the content.
5. Brush 1 coat over the area of repair
6. Cut a piece of the Polyester Fleece and place it over the 1st coat
7. Paint a final coat covering the fleece entirely.
8. If necessary, a Silver Coat Protection can be used to coat over the Turbo Poly Seal after it is cured to protect against ultraviolet light.

197 16

How to make a Shingle Roof Leak Repair. DIY is easy and cheap

Chapters:
0:00 SBS Cap sheet to patch shingle roof
0:47 Remember the Hook Blade- Important
1:05 Shingles are falling apart
1:34 Lifting up shingles
2:08 Installing the Cap sheet
4:51 Seal the joint between shingles
5:21 Turbo Poly Seal to seal shingle joints

50 7

How to repair TPO roof leaks
@AllRoof.
Super Silicone Seal – https://bergstromm.com/

70 8

Repair a skylight leak @AllRoof.
Super Silicone Seal – https://bergstromm.com/

73 4

An easy fix for chimney flashing leaks. Any homeowner can fix their own chimney leak very easily
Turbo Poly Seal – https://bergstromm.com/
@AllRoof.
7 Steps to Making a Roof Repair:
1. Locate the leaky area. Most likely around vent pipes, flashing, and penetrations through the roof
2. If necessary, brush off any dirt or debris so it is dust-free.
3. If cualking was used before, remove it.
4. Use Turbo Poly Seal – Stir the content.
5. Brush 1 coat over the area of repair
6. Cut a piece of the Polyester Fleece and place it over the 1st coat
7. Paint a final coat covering the fleece entirely.
8. If necessary, a Silver Coat Protection can be used to coat over the Turbo Poly Seal after it is cured to protect against Ultra Violets

159 12

Repairing EPDM Rubber Roof leak
Super Silicone Seal – https://bergstromm.com/product/black-super-silicone-seal-roof-leak-repair-1-gal/

468 16

Reviewing 2 Gutter filters. Which one is the best?
@FlatRoofDoctor Gutter filter – https://bergstromm.com/product/z-gutter-leaf-filter/

131.2K 828

The best Gutter leaf filter that never clogg
Z- Guuter Leaf Filter -https://bergstromm.com/product/z-gutter-leaf-filter/

152 30