Turbo Poly Seal Roof Leak Repair 1/2 Gal /Silver Coat/ 25′ Fleece/

https://bergstromm.com/
Watch this video on 3 different ways to repair a metal roof leak https://youtu.be/IgIz8s8UwTk
Fixing a leaky metal roof seam is very easy. Repairing a metal roof seam with Turbo Poly Seal is simple, and it is a Do It Yourself project. Metal roofs are excellent in general. Most issues are at transitions like seams and end flashing. A foam gasket https://bit.ly/3fLerF7 is used to seal between two panels or to prevent water from leaking at wall flashing or other transitions. These foam gaskets deteriorate over time, and water starts to leak in when it rains. Instead of replacing these rubber gaskets, we use Turbo Poly Seal (https://bergstromm.com/product/turbo-poly-seal-1-gal-50-ft-fleece/) to make the transition. It is a far better solution at a fraction of the cost. Turbo Poly Seal will adhere to metal, plastic, asphalt, and other surfaces.
read more and see more videos on my website Flat Roof Doctor https://flatroofdoc.com/turbo-poly-seal-leak-repair/

Five steps on how to use Turbo Poly Seal:
1. Clean the area from old caulking and tar
2. Remove rust with a grinder and steel bristle wire brush
3. Wipe the surface clean with lacquer thinners to ensure there is no silicone residue
4. Apply one coat of Turbo Poly Seal covering two inches on either side of crack or seam
5. Install the Polyester fleece over the layer of wet Turbo Poly Seal
6. Apply a second coat of Turbo Poly Seal covering material
7. If necessary, a final coat can be applied after several hours
To buy Turbo Poly Seal or Super Silicone Seal - https://bergstromm.com/product/turbo-poly-seal-1-gal-50-ft-fleece/

Steps on How to Repair a Metal Roof Seam that leak with Turbo Poly Seal
Metal Roof - 00:00
Metal Roof Seam leaking - 0:21
Screwing down new screws - 01:05
Applying Turbo Poly Seal 1st coat - 1:45
Showing Flexibility of Turbo Poly Seal - 02:06
Applying Polyester Fleece - 02:43
Difference between Turbo Poly Seal and Tar - 03:01
Applying 2nd Coat Turbo Poly Seal over Fleece - 03:47

1.8K 198

Flat Roof leak repair. How to install flashing on a commercial roof. Fix any water leak on all roofs. DIY When the existing flashing of roofs is messed up with tar and caulking don't worry. Watch this easy way to replace the flashing without removing the old.
Most leaks are from flashing on flat roofs

More videos on flashing - https://www.youtube.com/watch?v=XeOCA92h3pc

Leaks on Flat Roofs caused by flashing - https://www.youtube.com/watch?v=hNgUd00lDXw&t=9s

Turbo Poly Seal - https://bergstromm.com/product/turbo-poly-seal-1-gal-50-ft-fleece/

00:00 Start
00:20 Pointing the problems
01:19 Paint on Turbo Poly Seal
02:18 Second coat of Turbo poly Seal
03:15 Adding Granules on the Wet Turbo
04:38 Pointing Crack in the flashing
05:00 Sealing Crack on wall
05:27 The End Bla Bla Bla

Turbo Poly Seal https://bergstromm.com/
How to repair the flashing on a leaky flat roof.
Follow these steps:
1. Remove all old caulking and tar that was used to seal the flashing
2. Use an angle grinder with a hard-wire steel cone brush to remove about five inches of paint on the brick or cement wall above the metal flashing
3. Wipe the metal flashing thoroughly with lacquer thinners to remove any residue of silicone from the metal
4. Use masking tape to seal about three inches on the wall above the metal and also 2 inches below the grove on the metal. (this is for making it look clean when done)
5. Apply one coat of Turbo Poly Seal covering the entire area between the two masking tapes.
6. While wet, embed the Polyester Fleece into the Turbo Poly Seal
7. Apply a coat of Turbo Poly Seal to cover the entire fleece
8. Wait 10 min and then remove the masking tape.
8. After 30 minutes, the Turbo Poly Seal flashing can be painted with urethane-based paint.

430 59

I used 2 different products to repair leaks around A/C's and parapet walls. Amazing results from these 2 products.
Turbo Poly Seal - https://bergstromm.com/
Chapters:
0:00 Repairing Metal Roof leaks
0:35 Pitch Pocket leaking
1:51 Patch around A/C unit
3:30 Patch with Super Silicone Seal
#metalroofs
#leakrepair
#sealant

136 28

Flat Roof Leak Repair with Turbo Poly Seal - https://youtu.be/f6Vk2viMZyM
https://bergstromm.com/
To buy Turbo Poly Seal or Super Silicone Seal - https://bergstromm.com/
Which sealant is better, Turbo Poly Seal, Flex Seal, or Super Silicone Seal. See what I found and why one performs better than the other. I explain why one outperforms the other. It was a fantastic test that helps me understand what to look for.
Watch this video to see how to use Turbo Poly Seal on Flashing - https://youtu.be/hNgUd00lDXw
The one factor that sets Turbo Poly Seal and Super Silicone Seal apart from Flex Liquid or the Flex Spray is that Turbo Poly Seal And Super Silicone Seal come with polyester fleece. This polyester fleece makes these products super strong. Nothing can beat that combination.
Both Turbo Poly Seal and Super Silicone Seals perform well on metal roofs, asphalt roofs, and cement.
Super Silicone Seal is the best for use on EPDM Rubber roofs. This product will save you a lot of money. It is suitable for repairs and covering every seam to prevent the cover tape used on seams from deteriorating.
Steps on how to use Turbo Poly Seal or Super Silicone Seal:
1. Clean the surface from old caulking and tar where the repair is to be made
2. Wipe thoroughly clean with a rag and Lacquer Thinners or Acetone, which can be bought at Home Depot.
3. Mask off the area with masking tape allowing about 2 inches on either side of the seam or crack
4. Paint one thick coat between the masked off areas
5. Install the polyester fleece over the fresh coat of paint to cover the seam or crack 2 inches on each side
6. Apply another layer over the polyester fleece
7. Remove the masking tape after 10 minutes
Paint a third coat of Super Silicone Seal before removing the masking tape

0:00 Review on 5 products
0:11 water pressure test
0:25 Flex Seal tape
0:36 Flex Seal Liquid
0:51 Flex Seal Spray
1:22 Turbo Poly Seal
1:34 Super Silicone Seal
3:52 Filling pipe with water
7:00 Flexibility test on the metal seam
9:56 Results of the test
13:00 End

3.6K 304

An underground house. We used Turbo Poly seal to fix the leaks. Sealing concrete walls from leaking. Rodents ate on the plastic that was covering the outside concrete walls and roof of this underground house. See how to repair this

120 12

https://bergstromm.com/
This METAL ROOF REPAIR is a must-see for every owner that has a METAL ROOF. This is a very important repair that could save your roof from disaster.
To buy Turbo Poly Seal or Super Silicone Seal - https://bergstromm.com/
Many attempts have been taken to repair the seam on metal roofs without any success. Most people will use tar and caulking trying to fix or seal the overlapping panel seam on a metal roof. Tar will dry out and crack and caulking does not last.
Turbo Poly Seal is a tried and tested method to repair these seams. It is essential to prepare the surface properly to make this repair last.

Ten steps to repair a metal roof permanently:
1. Clean and remove all tar and caulking
2. Remove hex screws holding the two panels together
3. Remove the metal bar that was used to clamp the two panels together
4. Use an angle grinder with a stiff metal bristle to remove most of the silicone and tar
5. Use Lacquer Thinners to wipe clean the area
6. Fasten the overlapping metal seam with pan head screws leaving out the metal bracket
7. Apply one coat of Turbo Poly Seal covering about three inches on either side of the seam
8. Cut a polyester fleece to the size of one bay and place it over the wet painted coat of Turbo Poly Seal
9. Pait a final coat of Turbo Poly Seal covering the Polyester fleece.
10. After 24 hours, paint a coat of Aluminum Asphalt paint over the Turbo Poly Seal to protect it against ultraviolets

This repair will last many years if the preparation was done right.

0:00 Metal Roof Repair
0:41 Pointing out the issue on seams
0:55 Explaining about Aluminum Coating
2:10 Using Torch to remove Tar
2:37 Lot of rust under the tar
4:00 Scraping Tar off after heating it
4:55 found water and rust under metal strip
5:22 Angle grinder to remove rust
5:34 Replacing Hex screws with Pan Heads
6:00 Installing Turbo Poly Seal over the seam
7:25 Explaining why replacing screws
8:03 Teaching Jose English
8:35 Covering Turbo Poly Seal with Silver Coat

2K 167

https://bergstromm.com/
Quick tip on repairing a Vent pipe flashing leak on a metal roof. Vent pipe boots and rubber gaskets cause leaks when not maintained properly. Do not use silicone caulking to make repairs.
To buy Turbo Poly Seal or Super Silicone Seal - https://bergstromm.com/
This is a Polyurethane based product, and it sticks to everything. Almost no preparation is needed. Use a brush and scissors, and paint the Turbo Poly Seal on and you are done.
Steps on How to repair a vent pipe on a flat roof:
1. Clean the bent pipe and roof area around the vent pipe from old caulk and accessive tar
2. Mask off with masking tape the area around the vent pipe
3. Apply one coat of Turbo Poly Seal covering the roof surface and the vent pipe
4. Install the polyester fleece that was included in the Turbo Poly Seal kit over the fresh coat
5. Apply a final coat of Turbo Poly Seal covering the entire fleece and surface of the vent pipe area
6. After waiting 10 min, remove the masking tape
7. To ensure the Turbo Poly Seal lasts a long time, coat it with an oil base, urethane-based, or aluminum asphalt paint.
Summary:
It is important to do maintenance of a flat roof periodically. Check the pitch pockets, skylight flashing, and vent pipe flashing for cracks and repair accordingly.

0:00 How to repair a Vent Pipe Leak
0:48 Explaining why vent/stove pipes leak
1:31 Important tip - Pipe clamp
2:00 Important Tip - remove silicone
2:28 Replacing Hex screws with flathead screws
3:36 Applying Turbo Poly Seal on flashing
4:11 End

146 14

Vent pipes on roofs can cause leaks when the rubber boot disintegrates. See how to fix it without replacing it.

To buy Turbo Poly Seal or Super Silicone Seal - https://bergstromm.com/
How to repair a leak that comes from a bathroom vent pipe on a roof. Many times it is a simple object that sticks out from a roof like a vent pipe or chimney or a skylight that causes a leak. Most of the time it's the transition from the roof to the object that causes the leak. The transition is called the flashing. When a rubber membrane becomes separated from the flashing, then water will get in and cause damage to the underlayment.
A common way to fix this is to use caulking or roofing tar. That is a temporal solution. Tar dries up and crack and caulking shrinks and fails to seal for a long period of time.
We use a product called Turbo Poly Seal. This is a Polyurethane product that stays flexible and pliable no matter the conditions.
Watch the video to see how easy it is to make a repair on any flat roof permanently.
DIY

0:00 Vent Pipe Leak
0:32 Showing cracked rubber boot
1:00 applying Turbo Poly Seal
1:32 How to cut the fleece
1:45 Applying 1 st coat Turbo poly Seal
2:10 Embedding Fleece
2:57 Applying Top Coat Turbo Poly seal
3:07 Results

93 14

https://bergstromm.com/
METAL ROOF VENT PIPES cause leaks due to rubber boot that disintegrates.
We use this Turbo Poly Seal from - https://bergstromm.com/.com to repair leaks on any roof.
This product is Polyurethane based and adheres to any surface to accept EPDM Rubber. We use it on wood, cement, concrete, metal, glass asphalt base rubbers like Torch Down, and more.

To stop a leak on a metal roof is very easy. Do not use Tar or caulking. Tar and caulking will dry out and will make things worse. Turbo Poly Seal from Bergstrom Industries is specially formulated to make flashing repair on almost any type of roof. All you need is Turbo poly Seal, brush, and fleece and you can repair any leak.

0:00 Stop metal roof vents from leaking
0:15 Describing the problem
1:14 How to cut the fleece
2:29 Applying Turbo Poly Seal with brush
2:54 Embedding Fleece
3:19 Topcoat Turbo Poly Seal
5:42 End

166 24